This standard is issued under the fixed designation A ; the ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and are the. Buy ASTM Aa Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products from SAI Global. Buy ASTM A TEST METHODS, PRACTICES, AND TERMINOLOGY FOR CHEMICAL ANALYSIS OF STEEL PRODUCTS from SAI.

Author: Kagakasa Akinobar
Country: Azerbaijan
Language: English (Spanish)
Genre: Travel
Published (Last): 2 October 2010
Pages: 390
PDF File Size: 15.58 Mb
ePub File Size: 12.18 Mb
ISBN: 932-3-46997-756-3
Downloads: 93924
Price: Free* [*Free Regsitration Required]
Uploader: Voodooktilar

If the product analysis tolerance for such a chromium level is 0.

Current edition approved June 1, See Table 1 for normal elements and ranges for stainless steels. NIST does not produce reference standards suitable for all elements or all alloys.

Global organisations call on vehicle manufacturers to boost low carbon cars Jul. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if x751 revised, either reapproved or withdrawn. It includes both wet chemical and instrumental techniques. Unspecied Elements Note 4 7. If this heat analysis does not meet the heat analysis requirements of the specication, one sample from the product of each remelted ingot shall be analyzed, and the analyses shall meet the heat analysis requirements.

Your comments will receive a715 consideration at a meeting of the responsible technical committee, which you may attend. The heat analysis shall be obtained from one remelted ingot, or the product of one remelted ingot, from each primary melt.

Normal elements and ranges for stainless steels are as follows: The analysis shall meet the specied limits for heat analysis. Customer comments No comments were found for ASTM A – 11 standard test methods, practices, and terminology for chemical a715 of steel products. A β€” 07a Standard Test Methods, A7551, and Terminology for Chemical Analysis of Steel Products1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.


This standard has been approved for use by agencies of the Department of Defense. Cities, councils and businesses have teamed up to call on car manufacturers to boost production of Zero Emission Vehicles ZEVs.

ASTM International

Xstm applies only to product analysis and becomes meaningful only when the heat analysis of an element falls close to one of the specied limits. No comments were found for ASTM A – 11 standard test methods, practices, and terminology for chemical aztm of steel products. Approved June 1, It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

A superscript asym e indicates an editorial change since the last revision or reapproval. It does not apply to cast or heat analyses determined to show conformance to specied chemical limits.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

ASTM A – 11 standard test methods, practices, and terminology for chemical analysis of steel products 0. Cast or Heat Analysis 5. XXXX or may be expressed as a75 0.

ASTM International – Standard References for ASTM A – 14a

Committee A01 has identied the location of selected changes to this standard since the last issue A β€” 01 that may impact the use of this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.


Concerning the Specication of Chemical Composition Requirements 4. Through the new facility methane will Last previous edition approved in as A β€” It is intended that these test methods, practices, and terminology will contain all requirements for the determination of chemical composition of steel, stainless steel, or related alloys so that product specications will need contain only special modications and exceptions.

Proprietary methods are permissible provided the results are equivalent to those obtained from standard methods when applicable.

If signicant variations in heat or cast size are involved, a weighted average heat or cast analysis, based on the atm quantity of metal in each heat or cast, shall be reported. Be the first to comment! Examples of denitive analytical methods include gravimetric, coulometry, titrimetric based on normality, and mass spectrometry. The range of the specied composition applicable to product analysis is normally greater than that applicable to heat analysis in order to take into account deviations associated with analytical reproducibility Note 1 and the heterogeneity of the steel.

NOTE 4β€”All commercial metals contain small amounts of various elements in addition to those which are specied.