FERROLI P7 PDF

FERROLI WFL4+P7 PELLET ΤΑΞΙΑΡΩΝ. By – Ποιότητα & Οικονομία · Updated about 5 years ago · Taken in περιστερι · Already tagged. Gorilec na pelete Ferroli z visokim učinkom in omejenimi emisijami za kotle na trda goriva razreda 3 EN , zanesljiv, enostaven za uporabo in vzdrževanje.

Author: Zologor Madal
Country: Suriname
Language: English (Spanish)
Genre: Environment
Published (Last): 10 May 2009
Pages: 298
PDF File Size: 9.65 Mb
ePub File Size: 9.39 Mb
ISBN: 113-5-97986-937-5
Downloads: 18992
Price: Free* [*Free Regsitration Required]
Uploader: Shakagor

There are allot of those in our area and the price is half of the pellet.

FERROLI WFL4+P7 PELLET ΤΑΞΙΑΡΩΝ

Try with this, first measure your el. Hello, I have problem with my ferroli sun p7. Also, buy some high quality pellets a sack or two and see if the problem dissapears.

Now of course, because it burns wood pelletsit will slowly reach that power level. For the smoke problem see answer given to Safari.

This means that the parameters for each power level must be higher more pellets, more air. The increased flow of pellets on start up is ok if you have good quality pellets, and it seems you have. I will be back soon with more info!! And then start to blink A In other words, setting 1 can be set to have a efrroli power level or a high power level. The pellets filled the grille and almost all the metal neck.

To make sure that my signals are all correct, I have the terminals 7 and 8 as well as 13 and 14 bridged, without success. Feroli works and with pellet the setting was between 8 and 10 for a good flame result and with olive I was going ferrili to 17, which means LESS load.

The pellets of poor quality are easy to identify: We have also had a wood stove fitted in the lounge, a La Nordica Gemma, and we are using briquettes hot blocks with that, and it is wonderful. You can put it in power modulation mode and then it will change the quantity of pellets so that it matches the power needed.

The above way of switching between power levels seemed to me at that time quite pointless, so I switched back to frrroli mode. We have had no stuck pellets or any problems with this at all. Ash could be problem with pellet room heaters but with my big boiler I think I should be fine.

  GENTLEMEN OF BACONGO PDF

BRULEUR a Pellet FERROLI Sun P7

This is done every 5 seconds by default. This was a very weak bridge but it prevented the pellets to reach the fire so after a while the fire would die.

There are burners with a different design that are not so sensible to pellet quality. Well, i buy an house with central frroli system based on a diesel boiler, so i switch the burner to the sun P12 few days ago. If you scroll to next parameter too quick, the value will not be saved. We bought some cheaper pellets, aargh what a mistake, these were from Bosnia, never verroli will we buy them.

So our next job for Spring if not earlier is to purchase the Ferroli boiler, then there should be touch wood no problems. For example, if t07 is 15 seconds, and t09 is 5 seconds, then the burner will wait 10 seconds for the pellets to burn and 5 seconds will load pellets and then it will repeat.

Hi Antonis, I never tried to modulate the power; we were strugling with just making it work: This could be a good lead Thanks! Hi Safari, well you are the first person I hear that says the pellets are burning nicely.

Stuck SUN P7 pellet burner – how to fix. – Jurnal

The problem is that they are too small and tend to clog the burner right at the end of the pipe where the tube ends and enters the burner part. Did I really miss something or indeed the aforementioned description is really the way modulating mode does its job?

If you will use only one power level recommended until you ferrlli used with the verroli then it is necessary only to set the used power setting. Fedroli, we now understand that the conversion that we had done was not appropriate for our old oil burner, and the overheating came from the fact that the old boiler could not cope with the heat output. We did think that perhaps the fan had been installed incorrectly ie wired up wrong but upon further research today, that does not seem likely.

All these power levels are the same, they are just some settings, and you can make power level 1 as powerful as power level 5; all you have to do is to modify the two parameters of power level 1 to have the same values as power level 5. Also it can stop when it reaches 75 degrees u01but this is a safety feature.

  EVBU MY LOVE PDF

The burner SUN P7 from Ferroli has ferrolk minimum of automation, which means that is has no extra sensors apart from was is strictly ferdoli to function and for safety. Could you please explain how modulation mode exactly works? Buon Giorno mi son instalatore e servis per bruciattori e caldaia gas e gasolio in Croazia fiume Se avete instruzzioni come regolare brucciatore P7 e P 12 vi ferroki molto Salute da Fiume Heberling Ivo.

If you have t18 set to 0 and u02 set to 5 it means that the burner will start straight in power level 5.

This means that t07 is set to 15 seconds and t13 is set to 4. Power settings should be so that power level 1 is the smallest power and power level 5 is the highest you can actually set them anyway you want from the menu but for modulation they should be in ascending order, that is fan speed seeting and pelet quantity should increase from power level fertoli to power level 5. Hi Safari, great to hear all is good.

Thanks for the update Safari! I think you should call some local company to help you.

BRULEUR a Pellet FERROLI Sun P7 | eBay

Next issue is the pumps setup, they are in the hot line of the boiler, and they should be in the return line of the radiators circuit and hot water reservoir.

Is it the fan or the bearing? During this time only the fan works. For power level 3, t12 and t13 are used to control the fan t12 and the amount of pellets t After you have modified a value, you must wait 3 seconds for it to be saved! My question is, did you or anyone else maneged to get to reset this burner remotely with thermostat or some other device.

I press letter P oncenot hold 10 sec for parametar service, just once and enter in menu for programing automatic mode.